Heating a Shop or Detached Garage in Greenwood, AR: Which Option Fits

Is your shop too cold to use from Thanksgiving to March? Around Greenwood, plenty of homes have a detached garage or a metal shop out back, from the newer neighborhoods near town to the acreage off the county roads south and west of it. They’re great spaces nine months a year. Then a December cold snap hits, the concrete floor turns to ice under your boots, and the shop becomes a place you run into for a tool and run back out. The right heat for a shop depends far less on the heater than on how you use the building and how well it holds heat, so that’s where we start.

Here’s how we help Greenwood homeowners pick the option that fits.

Start With How You Use the Space

A shop you work in for a few hours on Saturdays needs something different from one you’re in every day. A space that only has to stay above freezing to protect a water line, paint, or batteries needs different heat than a finished garage used as an office or a gym. Before we talk equipment, we ask how often you’re out there, how warm you want it, whether you also want it cool in July, and whether you work with fuel, solvents, paint, or sawdust.

That last question matters. Anything with an open flame has to be placed and vented with what’s in the air in mind. If your shop is where you refinish furniture or work on engines, we need to know.

Insulation Comes Before Heat

An uninsulated metal building loses heat about as fast as you can make it. It also sweats. Warm, moist air hits cold steel and condenses, which drips on tools and rusts everything it lands on. A big roll-up door with no seal can leak as much heat as the rest of the building combined.

Spray foam, insulated panels, or at least sealing the big leaks and weatherstripping the doors can mean you need a much smaller heater, and the one you buy will actually keep up. We’ll tell you honestly if a building needs insulation before it’s worth heating.

Gas or Propane Unit Heaters

A ceiling-hung unit heater is the most common choice for a working shop that only needs heat. It warms the space fast, stays up out of the way, and works well with the door opening and closing all day. In town, a lot of Greenwood homes have natural gas that can be run out to the shop. Out in the county, propane from the tank that already feeds the house, or a separate tank, does the same job.

These heaters have to be vented properly, need a correctly sized gas line, and should be installed by someone who’ll check the gas pressure and the venting. Portable unvented heaters aren’t made for all-day use in a closed building.

Ductless Mini-Split Heat Pumps

If you want the shop warm in winter and cool in summer, a ductless mini-split is often the best fit. It mounts on the wall inside, with a small unit outside, runs on electricity, and heats efficiently through most of an Arkansas winter. It’s quiet, and there’s no flame, which is a plus in a shop with flammable materials. Mini-splits work best in a building that’s insulated, and on the coldest nights a well-chosen unit still carries the load. Bigger or divided shops may need more than one indoor head.

A Small Package Unit or Split System

For a large shop, a shop with an office or a finished room inside, or a building you want to treat like part of the house, a full system with ductwork can make sense. That might be a packaged unit sitting beside the building or a split system with an air handler or furnace inside. It gives you even heat and cooling across the whole space and real filtration, which helps in a dusty woodshop. New residential systems we install use R-454B refrigerant.

Why We Don’t Tie the Shop Into the House System

Homeowners ask whether they can just run a duct from the house. Almost always, no. Your home system was sized for your home, so adding a building means neither space gets enough. Ducts run underground or through the yard lose heat and pick up moisture. A separate system for the shop costs less to run in the end and won’t make the house uncomfortable.

🛠 What we do: we come out and measure the building, look at the insulation, doors, and windows, and figure out how much heat it needs, not just guess by square footage. We check your electrical panel for room for a mini-split, or the gas line or propane setup for a unit heater, and then lay out one or two options that fit how you’ll use the space. You’ll get a written quote before anything is installed.

Do I need to insulate before adding heat?

Not always, but it usually pays off. A small amount of sealing and insulation can cut the size of the heater you need and how much it costs to run.

Do I need a bigger electrical panel for a mini-split?

Sometimes. It depends on how much room your panel and the circuit to the shop have left. We check that on the first visit so there are no surprises.

Do I need to heat my shop all winter?

If there’s plumbing, paint, chemicals, or batteries out there, keeping it above freezing protects them. Most heaters can hold a low setting when you’re not using the space and warm it up when you are.

Comfortable Shop Heat for Greenwood Homes

Clark HVAC is a family-owned, licensed and insured heating and cooling company, and we install heating and cooling for homes, shops, and garages in Greenwood and across Sebastian County. 0% financing is available on qualifying installations, so you don’t have to put off a warm shop another winter. Call us and we’ll help you find the option that fits your building and how you use it.

📞 Call Now: 918-839-3734

Straight answers. Fair pricing. Clean work.

Next
Next

No Heat on a Cold Morning in Stigler, OK: What a Heating Service Call Looks Like